Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
|
yadif [2019/06/26 02:02] beandog |
yadif [2019/06/26 20:02] beandog |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== yadif ====== | ====== yadif ====== | ||
| + | |||
| + | * [[ffmpeg]] | ||
| + | * [[frameinfo]] | ||
| + | * [[detelecine]] | ||
| + | * ''man ffmpeg-filters'' | ||
| + | * [[https://ffmpeg.org/ffmpeg-filters.html#yadif-1]] | ||
| + | * [[https://wiki.videolan.org/Deinterlacing]] | ||
| + | |||
| + | * mode | ||
| + | * 0 / send_frame - Output one frame for each frame **(default)** | ||
| + | * 1 / send_field - Output one frame for each field (my preferred method) | ||
| + | * 2 / send_frame_nospatial - Like send_frame, but it skips the spatial interlacing check. | ||
| + | * 3 / send_field_nospatial - Like send_field, but it skips the spatial interlacing check. | ||
| + | |||
| + | <code> | ||
| + | parity | ||
| + | The picture field parity assumed for the input interlaced video. It accepts one of the following values: | ||
| + | |||
| + | 0, tff | ||
| + | Assume the top field is first. | ||
| + | |||
| + | 1, bff | ||
| + | Assume the bottom field is first. | ||
| + | |||
| + | -1, auto | ||
| + | Enable automatic detection of field parity. | ||
| + | |||
| + | The default value is auto. If the interlacing is unknown or the decoder does not export this information, top field first will be assumed. | ||
| + | |||
| + | deint | ||
| + | Specify which frames to deinterlace. Accept one of the following values: | ||
| + | |||
| + | 0, all | ||
| + | Deinterlace all frames. | ||
| + | |||
| + | 1, interlaced | ||
| + | Only deinterlace frames marked as interlaced. | ||
| + | |||
| + | The default value is all. | ||
| + | </code> | ||
| The best description I've seen of the filter options is here: [[https://www.avidemux.org/admWiki/doku.php?id=using:video_filter_yadif]] | The best description I've seen of the filter options is here: [[https://www.avidemux.org/admWiki/doku.php?id=using:video_filter_yadif]] | ||
| - | I use ''yadif'' on DVDs that have interlacing, and detelecine filters are not cleaning it up. | + | I use ''yadif'' on DVDs that have interlacing, and detelecine filters are not cleaning it up -- among my collection, it's pretty rare. Only two cartoon series, and three live action. |
| Command line for its default options: | Command line for its default options: | ||
| Line 11: | Line 51: | ||
| </code> | </code> | ||
| - | Using BeyBlade as a source: | + | Using BeyBlade as a source. |
| + | |||
| + | Default for ''mode'' is ''send_frame'', which will output one frame for each frame; the output frame rate is constant at 30000/1001 (29.97, NTSC). | ||
| + | |||
| + | If I set it to create a frame for each field (''mode=send_field''), it will come out at 60000/1001 constant instead (59.94). | ||
| {{::mpv-shot0001.png?direct|}} | {{::mpv-shot0001.png?direct|}} | ||
| + | |||
| + | {{::mpv-shot0002.png?direct|}} | ||
| + | |||
| + | {{::mpv-shot0003.png?direct|}} | ||
| + | |||
| + | Running defaults, or, just using ''-vf yadif'', the same frames in sequence: | ||
| + | |||
| + | {{::mpv-shot0004.png?direct|}} | ||
| + | |||
| + | {{::mpv-shot0005.png?direct|}} | ||
| + | |||
| + | {{::mpv-shot0006.png?direct|}} | ||
| + | |||
| + | I'm also not caring about video encoding quality right here, it's just default x265 settings. | ||
| + | |||
